Design Comfort Blog: Posts Tagged ‘Salt Lake City’

How to Monitor Heat Flow from Furnace Registers

Friday, March 16th, 2012

Of the many kinds of heating systems, forced air furnaces are among the simplest in Salt Lake City and monitoring the flow of heat is as simple as checking the registers and feeling the flow.

The Basics of Hot Air

At the furnace, usually in the basement or a central location, air is heated to a temperature set by the thermostat.  Once large and dominant, over the years, technological improvements have enabled furnaces to be much smaller and fit into closets.

With a fan, the warm air is circulated through a system of ducts and distributed at registers or grates usually in the floor.  A second grate takes the cooler air back to the furnace to be heated.

Water can be added at the furnace to humidify the air and filters are able to remove some of the dust that typically floats invisibly throughout a home.

Going With the Flow

While a forced air system tends to fluctuate between cycles, temperatures should be consistent throughout the home from room to room.  As heat is distributed, rooms get quickly warmer, then cool several degrees as heat dissipates until the thermostat setting starts the cycle over.

If there is poor circulation, the efficiency of the system is greatly reduced.  The furnace runs more often, adding strain and cost to the heating of your home.  Some rooms remain comfortable while the rise and fall of temperatures in others may be more radical or remain too cool.

Monitoring the Flow

By turning the thermostat higher, the furnace will engage and begin to force air to the registers.

Most registers have adjustable slats that can be rotated to allow more or less flow.  Checking to make sure all are fully open is the first step.  There is usually a lever or gear in obvious view.

Make sure all registers are free to allow air movement and not blocked by furniture or carpets.

After testing with your hand to see if there is adequate air flow, using an infrared or dial thermometer will more accurately identify if there are differences from register to register which could indicate a blockage of some sort in the vent or a problem with the system at the furnace.

Solutions

You should perform heating system maintenance on a yearly basis by contracting with a company like (Your Company) who can regularly change the filters, inspect the internal elements and ensure proper and efficient functioning of this most important part of your home.

Continue Reading

Tags: ,
Posted in Heating, heating system, Heating System Maintenance | Comments Off on How to Monitor Heat Flow from Furnace Registers

Causes of Delayed Furnace Ignition

Tuesday, February 28th, 2012

Delayed ignition in Salt Lake City is usually accompanied by a loud banging or booming sound that resembles a small explosion in your gas appliance. In a furnace, this can be terrifying and should never be ignored.

What Causes Delayed Ignition

Delayed ignition usually happens when you first turn on your furnace, often after a long delay between use, so usually early in the fall or late in the spring when you don’t necessarily have it on every day of the week.

What happens is moisture builds up over the course of a period of inactivity and begins to corrode the firebox in your furnace. That corrosion builds up to the point that it starts to block the ports that feed gas into the burners. When these ports get blocked, the burners down the line cannot light and when you flip the switch, they won’t light immediately.

Of course, while rust and corrosion are a risk, lint and dust can be equally problematic (and are more common if you don’t heating system maintenance properly each fall). Sulfur build up is also a possibility, as it is left behind by burning natural gas. It will appear as a layer of white on the surface of the burners or the pilot light.

When all of this happens and the ports are not cleaned properly, gas will build up in the chamber after it is turned on and, when it finally ignites, create the small boom sound. It doesn’t just sound like an explosion – it is one – and if ignored, it can become incredibly dangerous.

Solving the Problem

Delayed furnace ignition is an easy problem to avoid. All you need to do is have your furnace cleaned properly before turning it on each fall. A technician will clean the burners and ports and remove any dust, lint, rust or sulfur buildup that might block ignition and cause a delay.

When replacing your furnace, look for a device with corrosion resistant materials. You can learn more about these when it comes time to replace your furnace from a technician. Most importantly, be careful. It may be a small problem now, but if left to build up over time, that small boom can become a much larger one.  For help with this issue please call Design Comfort.

Continue Reading

Tags: , ,
Posted in Furnace, heating system | Comments Off on Causes of Delayed Furnace Ignition

Happy Valentine’s Day From Your HVAC Contractors!

Tuesday, February 14th, 2012

Everyone at Design Comfort wishes you a Happy Valentine’s Day! Valentine ’s Day is all about showing your appreciation for your loved ones. Whether it is your significant other, your family, or your friends, today is a great day to let them know how special they are to you. A handmade card, a bouquet of flowers, or even a simple phone call can make someone’s whole day.

If you are thinking about a big gift for your family, an upgrade to your HVAC system might not be the most romantic gift, but it is a gift that keeps on giving! An air filter will keep you indoor air clean, and a new furnace or heat pump will make your home more comfortable and lower your utility bills. Making your home cozier is something your whole family will appreciate!

Call Design Comfort to learn more about how some HVAC system upgrades improve the comfort level in your home. And to make your Valentine’s Day a little sweeter, here is a recipe for Chocolate Covered Strawberries

INGREDIENTS:

16 ounces milk chocolate chips

2 tablespoons shortening

1 pound fresh strawberries with leaves

DIRECTIONS:

  1. Insert toothpicks into the tops of the strawberries.
  2. In a double boiler, melt the chocolate and shortening, stirring occasionally until smooth. Holding them by the toothpicks, dip the strawberries into the chocolate mixture.
  3. Turn the strawberries upside down and insert the toothpick into styrofoam for the chocolate to cool.

For more details, visit allrecipes.com.

Continue Reading

Tags: ,
Posted in Air Filter, Furnace, Indoor Air Quality | Comments Off on Happy Valentine’s Day From Your HVAC Contractors!

What Does a Furnace Thermocouple Do?

Thursday, February 9th, 2012

In Salt Lake City modern appliances are equipped with an array of safety measures to make sure that they operate safely in your home. This includes gas furnaces, which are harmless when working correctly but can be unsafe if something goes wrong. Perhaps the most crucial safety feature of a gas furnace is the thermocouple, also called a flame sensor.

Essentially, a furnace thermocouple works as a kill switch to shut off the furnace in case the gas is not igniting, like if the pilot light is out. Here is how it works.

The thermocouple is made up of two pieces of metal which are welded together at one end, called the “hot end” because it actually sits directly in the path of the furnace flame. On the cold end, it is wired to a circuit. Under normal circumstances, when the furnace is switched on, gas flows through the line and is ignited by a pilot light, ignition spark or glow coil. The flame heats up the thermocouple, and the furnace stays on.

However, sometimes the gas may not ignite, for example if the pilot light is out or the glow coil is faulty. In these cases, if there were no thermocouple, gas would continue to flow out without being lit, creating a very dangerous, poisonous and potentially lethal situation.

What the thermocouple does is detect heat, so if the furnace is on, but the hot end of the thermocouple has not heated up, that circuit up at the cold end kills the power to the furnace so that gas cannot continue to flow out unchecked. That way, you do not have to worry about a gas leak building to dangerous levels without being aware of it.

Sometimes, the thermocouple can malfunction, causing the furnace to shut off even if the burners are working just fine. Usually that is just the result of build up on the hot end over time, which can be fixed with some sand paper or emery cloth.  If you have any questions about this please contact Design Comfort Co.

Continue Reading

Tags:
Posted in Furnace, Gas Heaters, Heating | Comments Off on What Does a Furnace Thermocouple Do?

HVAC Experts Answer “What Is Forced Air Heating?”

Thursday, February 2nd, 2012

As a Salt Lake City resident chances are that you’ve heard the term forced air heating before, particularly if you’re in the market for a new home heating system. But what does that actually mean? The truth is that if you’re asking this question, you’re not alone. There are so many types of home heating systems out there that it’s common to be a bit confused and overwhelmed by it all.

The truth is that a forced air heating system is simply a heating system that distributes heat throughout your house using air to carry it. In this type of system, heated air travels through a system of ducts and is expelled through vents into the different rooms and areas of your home in order to maintain a particular temperature. That temperature, of course, is whatever you set your thermostat to, and when the desired temperature is reached, the heat will shut off until the temperature drops down again.

The main difference between the different types of forced air heating systems is the type of equipment that heats the air. For instance, you could have a gas furnace, an electric furnace, a heat pump or a hydronic coil. All of these are capable of heating air, and when paired with a fan, blower or air handler, can distribute heated air throughout your home.

Many forced air heating systems are remarkably energy efficient and can effectively keep you home comfortable all winter long. Additionally, they are generally made to be incorporated with central air conditioning systems for year round temperature control. Heat pumps are especially convenient in this way, as they’re able to both heat and cool your home depending on the season and your home comfort needs.

Particularly if you already have ductwork in place or if you’re choosing a heating system for a new construction home, it can make a lot of sense to opt for some type of forced air heating. However, if you’re looking to replace an existing heating system in a house that doesn’t already have ductwork in place, the need to put it in can add a lot to the overall installation costs of the system.  Read more about the heating systems that Design Comfort Co services in our Heating section, or contact us today with any questions.

Continue Reading

Tags:
Posted in electric furnace, Heating, heating system | Comments Off on HVAC Experts Answer “What Is Forced Air Heating?”

Heating Installation Question: What Is an Electric Furnace?

Wednesday, January 25th, 2012

There are many types of furnaces in Salt Lake City that use a variety of energy sources to operate. Gas furnaces use natural or propane gas, boilers and radiators use water, heated by electricity. And then there are electric furnaces, which may have an advantage over other energy sources based on energy costs.

Simply put, electric furnaces function through the use of electricity. They do not require the use of any type of fuel – but function through wires and chords. An electric furnace uses heating coils, sometimes referred to as “resistance calrods” to create heat directly in the air flow. Inside the furnace cabinet are controls, a blower, and the circuit breakers for the heating elements. Some furnaces have the breakers accessible from the outside of the cabinet.

Other add-on accessories may include an electronic air cleaner, air filter, humidifier, high performance media filter, and air conditioning evaporator coil.

The heating process begins with the home’s thermostat. A drop in temperature is sensed by the thermostat, which alerts the electric furnace. The coil then warms up, thanks to the electric current that passes through it. The heated coil in turn heats the temperature of the air around it, which is then blown into the house through a blower. The pressure that is exerted by the blower on the heated air, warms it further. The blower is able to overcome the resistance of the duct work and replace unheated, colder air with the heated air. In most homes there are various return air ducts that are used to bring in the colder air to the furnace. This cold air travels through the furnace, through an air filter, the blower, and finally through the heat exchanger. After this it will then be pushed back into the house as warm air.

To maintain a supply of fresh air in the house, some furnaces also suck air from the atmosphere outside. After the air in the house reaches a particular temperature, the thermostat automatically shuts off the electric furnace.

An electric furnace may be less costly to run, depending on the price of electricity versus other sources like natural gas, propane gas, or oil. Gas and oil are fossil fuels and burning them leaves a “carbon footprint” – the release of carbon compounds and gases into the atmosphere. An electric furnace does not burn fuel and thus does not leave a carbon footprint. This electric warming process results in fewer particulates and contaminants in the air, too.

Continue Reading

Tags: , , ,
Posted in Heating | Comments Off on Heating Installation Question: What Is an Electric Furnace?

Heating Contractor Guide: Troubleshooting Furnace Air Flow Problems

Wednesday, January 18th, 2012

Whenever you notice furnace air flow problems in your Salt Lake City  home, you can usually do a little troubleshooting and solve the issue on your own. Most air flow problems can be fixed easily and quickly. Here are a few guidelines to get you started, but if you need help or notice other problems with your furnace, call a qualified Design Comfort heating technician.

Furnace Filters:

Checking the furnace filter is the first step you should take when there are any issues with your furnace, but especially with air flow problems. If a filter is dirty enough, the furnace will not come on at all. Ultimately, a clogged or dirty filter restricts the air flow, and this is the source of air flow problems ninety percent of the time.

Supply Registars and Cold Air Returns:

Once you’ve replaced or cleaned the filter, check your cold air returns, which are the vents that draw in the cold air in forced air systems. When a cold air return is blocked  by furniture or other obstructions, they cannot draw in enough air to allow the furnace to put out an adequate amount of hot air. Make sure they are open if nothing is blocking them.

Next, check your supply registers, which are the vents that supply the warm air, and make sure they are open as well. Whenever your heat is on, all of your supply registers should be open. Closing some vents will not increase the air flow in other vents in the house. Closing off one or two in areas where heat is not always needed will not hurt your system; however, when you close too many supply registers, it can cause problems with the ductwork and eventually damage the furnace if the air pressure is not correct.

If you continue to experience air flow problems, call a certified heating technician at Design Comfort. There could be a more serious issue, or if you have a newer furnace, your original ductwork could be the wrong size for that furnace model.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on Heating Contractor Guide: Troubleshooting Furnace Air Flow Problems

Heating Installation Guide: Benefits of Replacing Your Furnace

Wednesday, January 11th, 2012

You are about to make one of the largest purchases in your life – a new furnace for your Salt Lake City home. Maybe your old furnace is on life support and needs immediate replacement or you are looking for a better, more efficient furnace that will raise the comfort level of your home while reducing utility bills and carbon emissions.

If the furnace in your basement, crawl space, or attic is 15-20 years old, it may be a single-stage 80% percent efficient model, which doesn’t meet the higher efficiency standards of today’s models. It uses more energy, i.e. gas, oil, or electricity, to operate. And a single-stage furnace does not always provide even heating to all rooms in the home, based on the varying winter weather conditions. There may be large temperature variations from room to room.

Your new furnace will likely be more efficient and environmentally friendly than the one it is replacing – which are the two biggest benefits to replacing an old furnace. So, let’s take a closer look at these benefits, which link energy efficiency to the latest technology – namely two-stage furnaces and variable speed motors.

Two-stage furnaces start out by running in a first stage, which uses less than 70% of its capacity. This stage works well on moderate winter days. On colder days, the furnace will meet your extra heating demand by adjusting to the second stage in the heating cycle. Since the furnace spends most of its time operating in its lower capacity (first or single stage), it burns less fuel than a traditional furnace that always runs at full capacity and then shuts off when heating demand is met. You will see lower utility bills and a shorter payback period on your new furnace investment.

Variable-speed motors can actually save you money on your energy bill as they consume less electricity than standard motors. Variable speed furnaces save you money by having a higher SEER rating. SEER is the abbreviation for seasonal energy efficiency ratio. The higher the SEER, the more energy efficient the unit. The low operating costs of a variable speed furnace can allow you to run your furnace blower. With the low operating costs of the variable-speed furnace you can constantly run your blower without the worry of driving up your utility bill, allowing for continuously filtered air.

And when you shop for a new furnace, look for add-on equipment such as electronic air filters, humidifers, and programmable thermostats. Each will raise the comfort level you will be enjoying from Salt Lake City home’s your new furnace.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on Heating Installation Guide: Benefits of Replacing Your Furnace

Heating Tip: What to Check If Your Furnace Isn’t Lighting

Wednesday, January 4th, 2012

If your Salt Lake City home’s furnace isn’t lighting properly and your family is starting to suffer because of it, there are a number of possible problems you should check for before calling a professional. Some of these issues can be fixed quickly by you while others may be signs of a serious problem that needs professional attention right away.

Checking the Pilot Light

If you have a gas furnace, the first step is to check the pilot light and ensure it is still working properly. If the pilot light is still on but goes out when you try to light the furnace or simply won’t stay on when you relight it, you may need to have the gas valve replaced. In some cases, it is as simple as the pilot light not being large enough and the gas blowing out the light.

This happens when gas enters the chamber and doesn’t ignite right away. When it does ignite, which happens after more gas enters the chamber, the extra force of the ignition will blow out the light. This is still a problem and should be inspected to ensure you don’t have any potential gas related issues.

Still Not Lighting

If you don’t have a pilot light or the unit still isn’t lighting, it may be an electrical issue. Electrical ignitions for gas furnaces should spark when the thermostat is turned on, so if it doesn’t you know that the switch or relay are bad.

If you smell gas or anything similar in the room where the furnace is located, you should immediately turn off the unit and call your gas company, followed by a technician. There could be a leak causing low pressure that results in your pilot light going out. Whatever the case, you need someone to look at it immediately.

Your furnace should always turn on when you flip the switch and if it does not, assume there is a problem. If you cannot find the problem yourself and easily fix it, you should call a Salt Lake City heating contractor. The risk inherent in an improperly working furnace (especially gas or oil) is too high to ignore.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on Heating Tip: What to Check If Your Furnace Isn’t Lighting

How to Replace a Thermostat

Wednesday, December 28th, 2011

There are a lot of common household tasks that Salt Lake City do-it-yourselfers can handle beyond changing light bulbs or replacing a fuse. One of those is changing out a thermostat. The reasons for replacing a thermostat can vary from making an upgrade to changing out a thermostat that is not working right – or at all. Whatever the reason, the task is pretty simple and require s very little time and very few tools.

Let’s set the stage.

The materials you will need are the replacement thermostat, wire connectors, electrical tape (optional), needle nose pliers, and a screwdriver.

Here are the steps:

  1. Turn off electrical power to the existing thermostat. You can do this by flipping a breaker switch or removing a fuse from your home’s electrical panel. This would be a good time to make a note of the circuit’s location, writing the circuit number on the panel door or using a sticker.
  2. Remove the cover from the existing unit. You should be able to locate the screws that hold it to the wall mounting plate. Remove the screws and pull the unit away from the wall and mounting plate. Be careful not to touch the electrical wires together on the thermostat.
  3. Disconnect the wiring. Carefully remove the electrical wiring from the unit and keep the wires apart. You might want to tape the bare ends and also ensure that the wires don’t fall back through the wall. If the wires are not color coded, mark each one and which terminal they were removed from. Remove the mounting plate.
  4. If you are using a new mounting plate, make sure it fits over the existing hole and then pull the wires through the opening of the plate. Make sure the mounting plate is secured to the wall with the proper screws.
  5. Now match the wires to the terminals on the new thermostat. The wires are usually color-coded but if not, make sure you attach the right wires to the corresponding numbered terminals on the next thermostat. A green wire, which operates the furnace fan blower, is connected to the “G” terminal. The white wire operates the heater and attaches to the “W” terminal. The yellow wire operates the air conditioner and connects to the “Y” terminal. Use a wire nut to secure the wires and keep them apart from other wires. Ignore any other wires coming out of the wall as they are not necessary and may have been added by the original builder for other purposes.
  6. Carefully move the wires back into the wall as you line up the new thermostat on the mounting bracket. Install the new bracket and secure the thermostat to the bracket.
  7. Turn your power back on and check your thermostat by setting the temperature high or low, to engage the furnace or air conditioner.

This simple procedure can be done in less than 10 minutes. But if you have any doubts and want greater peace of mind, call a professional heating and cooling contractor to perform the installation.

Continue Reading

Tags: , ,
Posted in Heating | Comments Off on How to Replace a Thermostat