Design Comfort Blog

Heating Contractor Guide: Troubleshooting Furnace Air Flow Problems

January 18th, 2012

Whenever you notice furnace air flow problems in your Salt Lake City  home, you can usually do a little troubleshooting and solve the issue on your own. Most air flow problems can be fixed easily and quickly. Here are a few guidelines to get you started, but if you need help or notice other problems with your furnace, call a qualified Design Comfort heating technician.

Furnace Filters:

Checking the furnace filter is the first step you should take when there are any issues with your furnace, but especially with air flow problems. If a filter is dirty enough, the furnace will not come on at all. Ultimately, a clogged or dirty filter restricts the air flow, and this is the source of air flow problems ninety percent of the time.

Supply Registars and Cold Air Returns:

Once you’ve replaced or cleaned the filter, check your cold air returns, which are the vents that draw in the cold air in forced air systems. When a cold air return is blocked  by furniture or other obstructions, they cannot draw in enough air to allow the furnace to put out an adequate amount of hot air. Make sure they are open if nothing is blocking them.

Next, check your supply registers, which are the vents that supply the warm air, and make sure they are open as well. Whenever your heat is on, all of your supply registers should be open. Closing some vents will not increase the air flow in other vents in the house. Closing off one or two in areas where heat is not always needed will not hurt your system; however, when you close too many supply registers, it can cause problems with the ductwork and eventually damage the furnace if the air pressure is not correct.

If you continue to experience air flow problems, call a certified heating technician at Design Comfort. There could be a more serious issue, or if you have a newer furnace, your original ductwork could be the wrong size for that furnace model.

Read full article

Tags: , ,
Posted in Heating | Comments Off on Heating Contractor Guide: Troubleshooting Furnace Air Flow Problems

Happy Martin Luther King Day!

January 16th, 2012

Happy Martin Luther King Day! This holiday is not just about celebrating civil rights but also about serving your community. If you have the day off today, why not try spending it helping others? From volunteering at an animal shelter to helping the homeless, there are hundreds of ways you can make your community a better place to live. Have a great holiday!

Read full article

Tags:
Posted in Holiday | Comments Off on Happy Martin Luther King Day!

Heating Installation Guide: Benefits of Replacing Your Furnace

January 11th, 2012

You are about to make one of the largest purchases in your life – a new furnace for your Salt Lake City home. Maybe your old furnace is on life support and needs immediate replacement or you are looking for a better, more efficient furnace that will raise the comfort level of your home while reducing utility bills and carbon emissions.

If the furnace in your basement, crawl space, or attic is 15-20 years old, it may be a single-stage 80% percent efficient model, which doesn’t meet the higher efficiency standards of today’s models. It uses more energy, i.e. gas, oil, or electricity, to operate. And a single-stage furnace does not always provide even heating to all rooms in the home, based on the varying winter weather conditions. There may be large temperature variations from room to room.

Your new furnace will likely be more efficient and environmentally friendly than the one it is replacing – which are the two biggest benefits to replacing an old furnace. So, let’s take a closer look at these benefits, which link energy efficiency to the latest technology – namely two-stage furnaces and variable speed motors.

Two-stage furnaces start out by running in a first stage, which uses less than 70% of its capacity. This stage works well on moderate winter days. On colder days, the furnace will meet your extra heating demand by adjusting to the second stage in the heating cycle. Since the furnace spends most of its time operating in its lower capacity (first or single stage), it burns less fuel than a traditional furnace that always runs at full capacity and then shuts off when heating demand is met. You will see lower utility bills and a shorter payback period on your new furnace investment.

Variable-speed motors can actually save you money on your energy bill as they consume less electricity than standard motors. Variable speed furnaces save you money by having a higher SEER rating. SEER is the abbreviation for seasonal energy efficiency ratio. The higher the SEER, the more energy efficient the unit. The low operating costs of a variable speed furnace can allow you to run your furnace blower. With the low operating costs of the variable-speed furnace you can constantly run your blower without the worry of driving up your utility bill, allowing for continuously filtered air.

And when you shop for a new furnace, look for add-on equipment such as electronic air filters, humidifers, and programmable thermostats. Each will raise the comfort level you will be enjoying from Salt Lake City home’s your new furnace.

Read full article

Tags: , ,
Posted in Heating | Comments Off on Heating Installation Guide: Benefits of Replacing Your Furnace

Heating Tip: What to Check If Your Furnace Isn’t Lighting

January 4th, 2012

If your Salt Lake City home’s furnace isn’t lighting properly and your family is starting to suffer because of it, there are a number of possible problems you should check for before calling a professional. Some of these issues can be fixed quickly by you while others may be signs of a serious problem that needs professional attention right away.

Checking the Pilot Light

If you have a gas furnace, the first step is to check the pilot light and ensure it is still working properly. If the pilot light is still on but goes out when you try to light the furnace or simply won’t stay on when you relight it, you may need to have the gas valve replaced. In some cases, it is as simple as the pilot light not being large enough and the gas blowing out the light.

This happens when gas enters the chamber and doesn’t ignite right away. When it does ignite, which happens after more gas enters the chamber, the extra force of the ignition will blow out the light. This is still a problem and should be inspected to ensure you don’t have any potential gas related issues.

Still Not Lighting

If you don’t have a pilot light or the unit still isn’t lighting, it may be an electrical issue. Electrical ignitions for gas furnaces should spark when the thermostat is turned on, so if it doesn’t you know that the switch or relay are bad.

If you smell gas or anything similar in the room where the furnace is located, you should immediately turn off the unit and call your gas company, followed by a technician. There could be a leak causing low pressure that results in your pilot light going out. Whatever the case, you need someone to look at it immediately.

Your furnace should always turn on when you flip the switch and if it does not, assume there is a problem. If you cannot find the problem yourself and easily fix it, you should call a Salt Lake City heating contractor. The risk inherent in an improperly working furnace (especially gas or oil) is too high to ignore.

Read full article

Tags: , ,
Posted in Heating | Comments Off on Heating Tip: What to Check If Your Furnace Isn’t Lighting

Happy New Year’s Eve from Your Heating and Air Conditioning Contractor!

December 31st, 2011

Everyone here wishes you a Happy New Year! New Year’s is one of the best times to reflect on all the good things that have happened this year and make plans for the next. We hope that you are able to achieve all of your resolutions! If one of your resolutions is to be more environmentally friendly, remember that annual maintenance of your HVAC system will keep it running as efficiently as possible. And here is some New Year’s trivia to start your day: the first Time Square New Year’s Eve ball was dropped in 1907 after fireworks were banned in New York City. Today’s ball weighs nearly 12 thousand pounds and is 12 feet in diameter!

Read full article

Tags:
Posted in Holiday | Comments Off on Happy New Year’s Eve from Your Heating and Air Conditioning Contractor!

How to Replace a Thermostat

December 28th, 2011

There are a lot of common household tasks that Salt Lake City do-it-yourselfers can handle beyond changing light bulbs or replacing a fuse. One of those is changing out a thermostat. The reasons for replacing a thermostat can vary from making an upgrade to changing out a thermostat that is not working right – or at all. Whatever the reason, the task is pretty simple and require s very little time and very few tools.

Let’s set the stage.

The materials you will need are the replacement thermostat, wire connectors, electrical tape (optional), needle nose pliers, and a screwdriver.

Here are the steps:

  1. Turn off electrical power to the existing thermostat. You can do this by flipping a breaker switch or removing a fuse from your home’s electrical panel. This would be a good time to make a note of the circuit’s location, writing the circuit number on the panel door or using a sticker.
  2. Remove the cover from the existing unit. You should be able to locate the screws that hold it to the wall mounting plate. Remove the screws and pull the unit away from the wall and mounting plate. Be careful not to touch the electrical wires together on the thermostat.
  3. Disconnect the wiring. Carefully remove the electrical wiring from the unit and keep the wires apart. You might want to tape the bare ends and also ensure that the wires don’t fall back through the wall. If the wires are not color coded, mark each one and which terminal they were removed from. Remove the mounting plate.
  4. If you are using a new mounting plate, make sure it fits over the existing hole and then pull the wires through the opening of the plate. Make sure the mounting plate is secured to the wall with the proper screws.
  5. Now match the wires to the terminals on the new thermostat. The wires are usually color-coded but if not, make sure you attach the right wires to the corresponding numbered terminals on the next thermostat. A green wire, which operates the furnace fan blower, is connected to the “G” terminal. The white wire operates the heater and attaches to the “W” terminal. The yellow wire operates the air conditioner and connects to the “Y” terminal. Use a wire nut to secure the wires and keep them apart from other wires. Ignore any other wires coming out of the wall as they are not necessary and may have been added by the original builder for other purposes.
  6. Carefully move the wires back into the wall as you line up the new thermostat on the mounting bracket. Install the new bracket and secure the thermostat to the bracket.
  7. Turn your power back on and check your thermostat by setting the temperature high or low, to engage the furnace or air conditioner.

This simple procedure can be done in less than 10 minutes. But if you have any doubts and want greater peace of mind, call a professional heating and cooling contractor to perform the installation.

Read full article

Tags: , ,
Posted in Heating | Comments Off on How to Replace a Thermostat

Happy Holidays from Your Heating and Air Conditioning Contractor!

December 21st, 2011

Everyone at Design Comfort wishes you a very Happy Holiday! We hope you enjoy this time with friends, family and loved ones. Stay safe and warm this season! Also remember that whatever type of heating system you have, heating maintenance will keep your equipment running safely and at peak efficiency. If you haven’t had your annual checkup yet, we recommend you do so soon!

The holidays are a time to celebrate, and one of the best things about them is the great food. Here is a little treat we found that will make any day even better:

Gingersnap Cookies

“This melt-in-your-mouth ginger cookie recipe that I received from my grandmother has been enjoyed in my family since 1899.”

INGREDIENTS:

2 cups sifted all-purpose flour

1 tablespoon ground ginger

2 teaspoons baking soda

1 teaspoon ground cinnamon

1/2 teaspoon salt

3/4 cup shortening

1 cup white sugar

1 egg

1/4 cup dark molasses

1/3 cup cinnamon sugar

DIRECTIONS:

  1. Preheat oven to 350 degrees F (175 degrees C).
  2. Sift the flour, ginger, baking soda, cinnamon, and salt into a mixing bowl. Stir the mixture to blend evenly, and sift a second time into another bowl.
  3. Place the shortening into a mixing bowl and beat until creamy. Gradually beat in the white sugar. Beat in the egg, and dark molasses. Sift 1/3 of the flour mixture into the shortening mixture; stir to thoroughly blend. Sift in the remaining flour mixture, and mix together until a soft dough forms. Pinch off small amounts of dough and roll into 1 inch diameter balls between your hands. Roll each ball in cinnamon sugar, and place 2 inches apart on an ungreased baking sheet.
  4. Bake in preheated oven until the tops are rounded and slightly cracked, about 10 minutes. Cool cookies on a wire rack. Store in an air tight container.

For more details, visit allrecipes.com.

Read full article

Tags:
Posted in Holiday | Comments Off on Happy Holidays from Your Heating and Air Conditioning Contractor!

What to Do if Your Furnace Is Not Producing Enough Heat

December 14th, 2011

If your Salt Lake City home is cold, many blame the furnace for not bringing up the warm temperatures or they blame the thermostat for not working right.

It may very well be a thermostat issue – often caused by the location of the thermostat – that is causing the problem. However, sometimes root cause is found in the furnace or ventilation system.

Your indoor environment may be contributing to a seemingly slow-moving furnace. Your furnace may be working too hard to keep up with the heat demand because of an excessive build-up of dirt or debris on the filter or around the moving parts, such as the motor or fan belt. The most obvious thing to do is to keep the airflow unobstructed and keep all working parts clean.

First of all, you should regularly check your furnace filters and if they are dirty, replace them or clean them. Disposable furnace filters are relatively inexpensive and come in a variety of sizes and media ratings (ratings determine what size media is used and its ability to trap certain sized particulate). You can buy these individually or in bulk from a number of different resources. It is a good idea to replace the filters every three-six months.

Mesh filters can be removed, cleaned and reinserted. Like replaceable filters, mesh filters should be checked on a regular basis and then cleaned at least every three months.

You can remove the access panels to your furnace and inspect the components for any build-up of dust, dirt, or debris. Using a vacuum with an extension hose usually is all it takes to clean up the area.

Other reasons for poor heating performance include dirty or blocked ductwork. The harder your furnace has to work to push air through the ventilation system, the longer it takes to bring the heat up. Make your furnace work less and keep vents clear and ductwork clean.

Finally, the reason your furnace isn’t producing enough heat may not be the fault of your furnace at all – you may have a leaky house. But that’s a whole different story.

Read full article

Tags: , ,
Posted in Heating | Comments Off on What to Do if Your Furnace Is Not Producing Enough Heat

$35 Furnace Tune-up!

December 7th, 2011

If you have not had your annual maintenance visit, now is a great time! Design Comfort is offering a $35 furnace tune-up, usually $79! This tune-up includes everything you need to make sure your furnace is operating safely, such as a gas leak check, draft check, furnace check, and all furnace safeties. Keep your family safe and warm this winter, and do so at an incredible price!

And we have an even better deal too: get a FREE Furnace Safety Inspection with the purchase of our annual maintenance plan. Annual maintenance will keep your heating and cooling system working at peak efficiency and cut down on future repairs. Our Priority One Maintenance Program will also get you preferred service, 20 % off parts and repairs, and no after-hours charge.  Don’t miss out on either of these great deals, call Design Comfort today!

Regular Hours Only. Not available with any other promotions or offers.

Read full article

Tags: , ,
Posted in Heating | Comments Off on $35 Furnace Tune-up!

How Do I Check a Gas Furnace Draft Pressure Switch?

November 30th, 2011

There are many reasons why a furnace stops working and in many cases, a Salt Lake City homeowner can perform some simple diagnostics to pinpoint the problem. Finding the problem is one thing – fixing it is another. When in doubt, don’t try it yourself. Call a qualified professional.

But let’s look at one possible problem and solution you may be able to perform yourself – testing the draft pressure switch. The draft pressure switch on a gas furnace allows an electrical current to pass through to ignite the furnace. The pressure switch monitors the draft conditions and won’t allow the furnace’s gas valve to open unless draft is correct.

If the switch is malfunctioning, so too will (or will not) the furnace.

The best way to locate the switch is by consulting with your owner’s manual or by going online and simply typing in the words “gas furnace draft switch.” It is identifiable by its round size and is bolted to the outside of the furnace. It should be nearby the draft inducer motor because the two are connected by a metal tube. The tube may sometimes be the culprit, too. A tube that is blocked with condensation may cause the switch to go bad.

To check for proper function, first turn off power to the furnace, either by shutting down the ‘on’ switch at the furnace or shutting off the circuit breaker.

Use a volt ohm meter to check if the switch is opening and closing properly. Start by zeroing out the meter’s probes by touching the tips together. Using the dial (could be analog or digital), set the meter to 24 volts. Ground the black probe by attaching it to any metal part of the furnace. Then place the end of the red probe on the metal tube connecting the draft pressure switch to the draft inducer motor.

If the switch is working properly the meter should read at least 24 volts, or very near that. If the reading is short of 24 volts, the switch is not working correctly. At that point you may decide to replace it or call a professional to do the task (recommended).

Always remember that there are many sources which will help you diagnose and repair a problem, especially those available through the Internet. If you search YouTube.com you will find many videos advising you on how to repair certain components. Use all of the resources available to you and keep the phone number of a qualified and professional heating and cooling contractor nearby.

Read full article

Tags: , ,
Posted in Heating | Comments Off on How Do I Check a Gas Furnace Draft Pressure Switch?